Furnace Repair North Vancouver, Service & Installation

If your furnace isn’t working, there are a couple things you can check before calling us about furnace repair North Vancouver work. Occasionally we arrive at a home only to find the thermostat setting had been lowered, so that is what you should check first.

If the circuit breaker for your furnace has tripped go ahead and reset it, but if it trips again you have a problem that needs to be dealt with by a professional. That goes for the pilot light too: if it goes out, again and again, you need our help.

It doesn’t matter what brand of furnace is in your home, or whether it uses gas or electricity. Our certified technicians can handle them all, except for oil-fired furnaces. Gas furnace service and cleaning is our specialty and we've help countless families sleep better knowing their heating system is working properly and energy efficient. One thing we like to suggest is to set up a regular furnace maintenance program so you can enjoy a clean, safe heating season and save money on fuel bills.

Forced-air furnaces are reliable, but cleaning and regular maintenance is required to keep energy costs down. Since 2010 only high-efficiency furnaces have been installed in Canadian homes. They are technological wonders but far more elaborate than the older furnaces that many of us grew up with. Our furnace cleaning service and furnace maintenance service is done by trained heating technicians.

Scheduling annual furnace maintenance will greatly reduce the likelihood of an emergency furnace repair situation and your furnace will operate more efficiently, reducing your heating bills. Also, an efficient furnace is healthier for your family. We focus on helping you avoid an unnecessary furnace replacement by keeping it working at peak efficiency. 

• Annual maintenance of forced-air furnaces includes:
• Thorough diagnostic check
• Furnace blower removed and cleaned
• Blower compartment cleaned
• Furnace, burners, venting/flue pipe and heat exchanger cleaned
• Blower motor checked, cleaned and lubricated (if necessary)
• New filter installed
• Furnace ignition and blower operation tested

A furnace, referred to as a heater or boiler in British English, is heating equipment used to heat up an entire building. Furnaces are mostly used as a major component of a central heating system. The name derives from Latin word fornax, which means oven. Furnaces are permanently installed to provide heat to an interior space through intermediary fluid movement, which may be air, steam, or hot water. Heating appliances that use steam or hot water as the fluid are normally referred to as a residential steam boiler or residential hot water boiler.

The most common fuel source for modern furnaces (natural gas) in North America and much of Europe is for natural gas furnaces; other common fuel sources include LPG (liquefied petroleum gas), fuel oil, wood and in rare cases coal. In some areas electrical resistance heating is used, especially where the cost of electricity is low or the primary purpose is for indoor air quality.

Modern high-efficiency furnaces can be up to 98% efficient and operate without a chimney, with a typical gas furnace being about 80% efficient. Waste gas and heat are mechanically ventilated through PVC pipes that can be vented through the side or roof of the house. Fuel efficiency in this type of furnace is measured in AFUE (Annual Fuel Utilization Efficiency). Furnaces primarily run on natural gas or electricity. 

A furnace room is a mechanical room in a building for locating a furnace and auxiliary equipment. Such a room minimizes the visual impact of the furnace, pipes and other gear. A modern compact furnace for a single family home can readily fit into a small closet. However, care must be exercised to provide adequate ventilation as the exterior of the furnace unit emits a significant amount of heat, and a natural gas or any other fueled furnace will need an adequate amount of combustion air.

A garage should never be used as a furnace room for a number of reasons. Air leakage around the connecting ductwork and other needed passages could act to transport potentially dangerous contaminants (including carbon monoxide) from the garage into the main body of the house, ductwork and other passages between the garage and the living areas of the house could be breaches of the required fire resistant barrier between these two areas, a furnace or other such appliance would need to be protected from potential vehicle impact by bollards or some other means, and any ignition source in a garage is required to be at least 18 inches above the floor level due to the potential of explosive gasoline vapors in any garage. In the picture, the airflow is from bottom to top, with an electronic air filter on the bottom, followed by a natural gas high efficiency or condensing furnace (98% efficient) in the middle, and air conditioning coils on top.

Save money and increase your heating system's energy efficiency and comfort by following these simple steps to keep your furnace in tip-top condition.

For a DIY furnace tune-up, first flip the electrical power switch to “Off.” Remove the combustion chamber door by lifting up and pulling it out, and remove the burner flame cover (if you have one). It’s usually held in place by two screws.

Burner Flames



Look at the burner flames. The flames should be fairly even and blue. A yellow flame indicate dirty burners. (Don’t breathe on the flames because the extra oxygen will also make them turn yellow.) Don’t play with the flame sensor or adjust the burners yourself. Call in a pro.

Vacuum

Vacuum everywhere you see dust. While everything is open, use a flashlight to look for signs of soot (fine black powder), which often indicates poor combustion. Lift off the lower door (blower door) and vacuum the blower compartment.

The Blower

Remove the blower (also called a squirrel cage) in order to clean it. If you have a control panel in front of the blower, two screws will loosen it and you can let it hang. Next, using a 7/16-in. socket and ratchet, remove the two bolts that hold the blower in place, then gently lift it out.

Clean the blower blades thoroughly with a vacuum and small brush. Take care not to stress the wiring or disturb the counterweights that will be on the fan blades. If you can’t clean the blower thoroughly, don’t clean it at all; you could throw it off balance.

The Filter

Change dirty filters every one to three months. A low cost fiberglass filter will adequately protect the blower and blower motor. If you want to install a more expensive, high-efficiency filter, check the owner’s manual for the manufacturer recommendations. If in doubt you can always call us for professional heating service.

There's a lot more involved in furnace maintenance services, so if you would like to read the full article click here for that.

It is recommended to have your furnace serviced every year. We provide great customer service, so call today and set up an appointment.